Inhaled drug delivery: a randomized study in intubated patients with healthy lungs.

BACKGROUND: The administration technique for inhaled drug delivery during invasive ventilation remains debated. This study aimed to compare in vivo and in vitro the deposition of a radiolabeled aerosol generated through four configurations during invasive ventilation, including setups optimizing drug delivery. METHODS: Thirty-one intubated postoperative neurosurgery patients with healthy lungs were randomly assigned to four configurations of aerosol delivery using a vibrating-mesh nebulizer and specific ventilator settings: (1) a specific circuit for aerosol therapy (SCAT) with the nebulizer placed at 30 cm of the wye, (2) a heated-humidified circuit switched off 30 min before the nebulization or (3) left on with the nebulizer at the inlet of the heated-humidifier, (4) a conventional circuit with the nebulizer placed between the heat and moisture exchanger filter and the endotracheal tube. Aerosol deposition was analyzed using planar scintigraphy. RESULTS: A two to three times greater lung delivery was measured in the SCAT group, reaching 19.7% (14.0-24.5) of the nominal dose in comparison to the three other groups (p < 0.01). Around 50 to 60% of lung doses reached the outer region of both lungs in all groups. Drug doses in inner and outer lung regions were significantly increased in the SCAT group (p < 0.01), except for the outer right lung region in the fourth group due to preferential drug trickling from the endotracheal tube and the trachea to the right bronchi. Similar lung delivery was observed whether the heated humidifier was switched off or left on. Inhaled doses measured in vitro correlated with lung doses (R = 0.768, p < 0.001). CONCLUSION: Optimizing the administration technique enables a significant increase in inhaled drug delivery to the lungs, including peripheral airways. Before adapting mechanical ventilation, studies are required to continue this optimization and to assess its impact on drug delivery and patient outcome in comparison to more usual settings.

A large-volume low-pressure nasal irrigation delivers drug into the nasal cavity? An in vivo study.

The nasal administration route emerged as an interesting route in systemic and brain drug delivery, and different modalities of nasal delivery are available. The nasal irrigation is one of them, but there is a lack of studies investigating the distribution of a large-volume irrigation. The main aim of this study was to assess the deposition of radiolabeled saline in the nasal cavities and paranasal sinuses following nasal irrigation by imaging. Five healthy males volunteered to perform large-volume low-pressure nasal irrigation, with a douching device containing 50 mL of radiolabeled isotonic saline. Participants underwent a scintigraphy immediately after. Both the nasal cavities and maxillary sinuses were systematically reached by the solution during nasal irrigation. The sinuses set in a lower position during nasal irrigation showed a tendency to be more irrigated than the sinuses set in a higher position (7.67% vs 22.72%; p = 0.086). Moreover, substantial inter- and intraindividual heterogeneity regarding solution deposition was observed. Large-volume low-pressure nasal irrigation is a good modality to reach the maxillary sinuses as well as the nasal cavities. In order to ensure adequate reaching of both nasal cavities and paranasal sinuses, nasal irrigation should be performed bilaterally.

Influence of mesh nebulizer characteristics on aerosol delivery in non-human primates.

Non-Human Primates (NHPs) are particularly relevant for preclinical studies during the development of inhaled biologics. However, aerosol inhalation in NHPs is difficult to evaluate due to a low lung deposition fraction and high variability. The objective of this study was to evaluate the influence of mesh nebulizer parameters to improve lung deposition in macaques. We developed a humidified heated and ventilated anatomical 3D printed macaque model of the upper respiratory tract to reduce experiments with animals. The model was compared to in vivo deposition using 2D planar scintigraphy imaging in NHPs and demonstrated good predictivity. Next, the anatomical model was used to evaluate the position of the nebulizer on the mask, the aerosol particle size and the aerosol flow rate on the lung deposition. We showed that placing the mesh-nebulizer in the upper part of the mask and in proximal position to the NHP improved lung delivery prediction. The lower the aerosol size and the lower the aerosol flow rate, the better the predicted aerosol deposition. In particular, for 4.3 ± 0.1 µm in terms of volume mean diameter, we obtained 5.6 % ± 0.2 % % vs 19.2 % ± 2.5 % deposition in the lung model for an aerosol flow rate of 0.4 mL/min vs 0.03 mL/min and achieved 16 % of the nebulizer charge deposited in the lungs of macaques. Despite the improvement of lung deposition efficiency in macaques, its variability remained high (6-21 %).

There Is a Risk of Spread During a Nebulization Session in a Patient with COVID-19.

Introduction: A hypothetical risk of SARS-CoV-2 airborne transmission through nebulization was suggested based on a potential environmental contamination by the fugitive aerosol emitted in the environment during the procedure. The aim of this study was to verify this risk from the fugitive aerosol emitted by COVID-19 patients during one nebulization session. Methods: In this cohort study, COVID-19 patients treated with nebulization were recruited at their admission to the hospital. Patients had to perform a nebulization session while a BioSampler® and a pump were used to vacuum the fugitive aerosol and collect it for SARS-CoV-2 RNA detection. Results: Ten consecutive patients hospitalized with COVID-19 were recruited. The median viral load was 6.5 × 106 copies/mL. Two out of the 10 samples from the fugitive aerosol collected were positive to SARS-CoV-2. Conclusion: The risk of fugitive aerosol contamination with SARS-CoV-2 during nebulization has now been verified.

Aerosol therapy in adult critically ill patients: a consensus statement regarding aerosol administration strategies during various modes of respiratory support.

BACKGROUND: Clinical practice of aerosol delivery in conjunction with respiratory support devices for critically ill adult patients remains a topic of controversy due to the complexity of the clinical scenarios and limited clinical evidence. OBJECTIVES: To reach a consensus for guiding the clinical practice of aerosol delivery in patients receiving respiratory support (invasive and noninvasive) and identifying areas for future research. METHODS: A modified Delphi method was adopted to achieve a consensus on technical aspects of aerosol delivery for adult critically ill patients receiving various forms of respiratory support, including mechanical ventilation, noninvasive ventilation, and high-flow nasal cannula. A thorough search and review of the literature were conducted, and 17 international participants with considerable research involvement and publications on aerosol therapy, comprised a multi-professional panel that evaluated the evidence, reviewed, revised, and voted on recommendations to establish this consensus. RESULTS: We present a comprehensive document with 20 statements, reviewing the evidence, efficacy, and safety of delivering inhaled agents to adults needing respiratory support, and providing guidance for healthcare workers. Most recommendations were based on in-vitro or experimental studies (low-level evidence), emphasizing the need for randomized clinical trials. The panel reached a consensus after 3 rounds anonymous questionnaires and 2 online meetings. CONCLUSIONS: We offer a multinational expert consensus that provides guidance on the optimal aerosol delivery techniques for patients receiving respiratory support in various real-world clinical scenarios.

Administration of Bacteriophages via Nebulization during Mechanical Ventilation: In Vitro Study and Lung Deposition in Macaques.

Bacteriophages have been identified as a potential treatment option to treat lung infection in the context of antibiotic resistance. We performed a preclinical study to predict the efficacy of delivery of bacteriophages against Pseudomonas aeruginosa (PA) when administered via nebulization during mechanical ventilation (MV). We selected a mix of four anti-PA phages containing two Podoviridae and two Myoviridae, with a coverage of 87.8% (36/41) on an international PA reference panel. When administered via nebulization, a loss of 0.30-0.65 log of infective phage titers was measured. No difference between jet, ultrasonic and mesh nebulizers was observed in terms of loss of phage viability, but a higher output was measured with the mesh nebulizer. Interestingly, Myoviridae are significantly more sensitive to nebulization than Podoviridae since their long tail is much more prone to damage. Phage nebulization has been measured as compatible with humidified ventilation. Based on in vitro measurement, the lung deposition prediction of viable phage particles ranges from 6% to 26% of the phages loaded in the nebulizer. Further, 8% to 15% of lung deposition was measured by scintigraphy in three macaques. A phage dose of 1 × 109 PFU/mL nebulized by the mesh nebulizer during MV predicts an efficient dose in the lung against PA, comparable with the dose chosen to define the susceptibility of the strain.

Comparison of Aerosol Deposition Between a Cynomolgus Macaque and a 3D Printed Cast Model of the Animal.

PURPOSE: Preclinical aerosol studies using animals are essential for evaluating toxic or therapeutic effects on human respiratory tract. Macaques are relevant animal models for respiratory studies, but they are sensitive, expensive and difficult-to-access. METHODS: In the context of preliminary studies before animal experiments, we set up an alternative in vitro anatomical model of macaque airways to reduce, refine and replace (3Rs) the animals. We printed an in vitro anatomical cast until the third bronchial division from X-ray computed tomography data of a healthy cynomolgus macaque. This in vitro model was then connected to a respiratory pump to mimic macaque's breathing. We assessed the relevance of this in vitro model, by comparing aerosol deposition patterns obtained with the anatomical model and in three macaques using planar gamma camera imaging. DTPA-99mTechnetium aerosols were produced using three jet nebulizers, generating three different particle sizes: 13.1, 3.2 and 0.93 µm in terms of the mass median aerodynamic diameter (MMAD). RESULTS: The data showed no statistical differences between the animal and anatomical in vitro models in terms of total aerosol deposited in the airways. However, the distribution of the deposition in the airways showed a higher deposited fraction in the upper respiratory tract in the animals than the in vitro model for all particle sizes. CONCLUSIONS: The anatomical printed model appears to be a relevant in vitro tool to predict total aerosol deposition in macaque airways.

Nebulized fusion inhibitory peptide protects cynomolgus macaques from measles virus infection.

Measles is the most contagious airborne viral infection and the leading cause of child death among vaccine-preventable diseases. We show here that aerosolized lipopeptide fusion inhibitor, derived from heptad-repeat regions of the measles virus (MeV) fusion protein, blocks respiratory MeV infection in a non-human primate model, the cynomolgus macaque. We use a custom-designed mesh nebulizer to ensure efficient aerosol delivery of peptide to the respiratory tract and demonstrate the absence of adverse effects and lung pathology in macaques. The nebulized peptide efficiently prevents MeV infection, resulting in the complete absence of MeV RNA, MeV-infected cells, and MeV-specific humoral responses in treated animals. This strategy provides an additional means to fight against respiratory infection in non-vaccinated people, that can be readily translated to human trials. It presents a proof-of-concept for the aerosol delivery of fusion inhibitory peptides to protect against measles and other airborne viruses, including SARS-CoV-2, in case of high-risk exposure.

Nebulized fusion inhibitory peptide protects cynomolgus macaques from measles virus infection.

Measles is the most contagious airborne viral infection and the leading cause of child death among vaccine-preventable diseases. We show here that aerosolized lipopeptide fusion inhibitors, derived from heptad-repeat regions of the measles virus (MeV) fusion protein, block respiratory MeV infection in a non-human primate model, the cynomolgus macaque. We used a custom-designed mesh nebulizer to ensure efficient aerosol delivery of peptides to the respiratory tract and demonstrated the absence of adverse effects and lung pathology in macaques. The nebulized peptide efficiently prevented MeV infection, resulting in the complete absence of MeV RNA, MeV-infected cells, and MeV-specific humoral responses in treated animals. This strategy provides an additional shield which complements vaccination to fight against respiratory infection, presenting a proof-of-concept for the aerosol delivery of fusion inhibitory peptides to protect against measles and other airborne viruses, including SARS-CoV-2, in case of high-risk exposure, that can be readily translated to human trials.

Inhaled amikacin versus placebo to prevent ventilator-associated pneumonia: the AMIKINHAL double-blind multicentre randomised controlled trial protocol.

INTRODUCTION: Pre-emptive inhaled antibiotics may be effective to reduce the occurrence of ventilator-associated pneumonia among critically ill patients. Meta-analysis of small sample size trials showed a favourable signal. Inhaled antibiotics are associated with a reduced emergence of antibiotic resistant bacteria. The aim of this trial is to evaluate the benefit of a 3-day course of inhaled antibiotics among patients undergoing invasive mechanical ventilation for more than 3 days on the occurrence of ventilator-associated pneumonia. METHODS AND ANALYSIS: Academic, investigator-initiated, parallel two group arms, double-blind, multicentre superiority randomised controlled trial. Patients invasively ventilated more than 3 days will be randomised to receive 20 mg/kg inhaled amikacin daily for 3 days or inhaled placebo (0.9% Sodium Chloride). Occurrence of ventilator-associated pneumonia will be recorded based on a standardised diagnostic framework from randomisation to day 28 and adjudicated by a centralised blinded committee. ETHICS AND DISSEMINATION: The protocol and amendments have been approved by the regional ethics review board and French competent authorities (Comité de protection des personnes Ouest I, No.2016-R29). All patients will be included after informed consent according to French law. Results will be disseminated in international scientific journals. TRIAL REGISTRATION NUMBERS: EudraCT 2016-001054-17 and NCT03149640.

Inhaled bacteriophage therapy in a porcine model of pneumonia caused by Pseudomonas aeruginosa during mechanical ventilation.

BACKGROUND AND PURPOSE 255: Pseudomonas aeruginosa is a main cause of ventilator-associated pneumonia (VAP) with drug-resistant bacteria. Bacteriophage therapy has experienced resurgence to compensate for the limited development of novel antibiotics. However, phage therapy is limited to a compassionate use so far, resulting from lack of adequate studies in relevant pharmacological models. We used a pig model of pneumonia caused by P. aeruginosa that recapitulates essential features of human disease to study the antimicrobial efficacy of nebulized-phage therapy. EXPERIMENTAL APPROACH: (i) Lysis kinetic assays were performed to evaluate in vitro phage antibacterial efficacy against P. aeruginosa and select relevant combinations of lytic phages. (ii) The efficacy of the phage combinations was investigated in vivo (murine model of P. aeruginosa lung infection). (iii) We determined the optimal conditions to ensure efficient phage delivery by aerosol during mechanical ventilation. (iv) Lung antimicrobial efficacy of inhaled-phage therapy was evaluated in pigs, which were anaesthetized, mechanically ventilated and infected with P. aeruginosa. KEY RESULTS: By selecting an active phage cocktail and optimizing aerosol delivery conditions, we were able to deliver high phage concentrations in the lungs, which resulted in a rapid and marked reduction in P. aeruginosa density (1.5-log reduction, p < .001). No infective phage was detected in the sera and urines throughout the experiment. CONCLUSION AND IMPLICATIONS: Our findings demonstrated (i) the feasibility of delivering large amounts of active phages by nebulization during mechanical ventilation and (ii) rapid control of in situ infection by inhaled bacteriophage in an experimental model of P. aeruginosa pneumonia with high translational value.

Non-human primate models of human respiratory infections.

Respiratory pathogens represent a great burden for humanity and a potential source of new pandemics, as illustrated by the recent emergence of coronavirus disease 2019 (COVID-19). In recent decades, biotechnological advances have led to the development of numerous innovative therapeutic molecules and vaccine immunogens. However, we still lack effective treatments and vaccines against many respiratory pathogens. More than ever, there is a need for a fast, predictive, preclinical pipeline, to keep pace with emerging diseases. Animal models are key for the preclinical development of disease management strategies. The predictive value of these models depends on their ability to reproduce the features of the human disease, the mode of transmission of the infectious agent and the availability of technologies for monitoring infection. This review focuses on the use of non-human primates as relevant preclinical models for the development of prevention and treatment for human respiratory infections.

Pressurized Metered Dose Inhaler Aerosol Delivery Within Nasal High-Flow Circuits: A Bench Study.

Background: Obstructive patients may benefit from nasal high-flow (NHF) therapy, but the use of pressurized metered-dose inhalers (pMDIs) has not been evaluated in this situation. Methods: Using an adult circuit and medium-sized cannula, we have tested different NHF rates, pMDI positions, breathing patterns, spacers, and spacer orientation. First, we evaluated albuterol delivery at the nasal cannula outlet. The second set of experiments made use of a nasopharyngeal cast to estimate the mass of albuterol potentially reaching the lungs. Albuterol was caught on filters placed at the cannula outlet and downstream of the nasal cast, and albuterol was quantified by spectrophotometry. Results: The highest amounts of albuterol delivered at the cannula outlet were observed with a 30 L/min flow rate (vs. 45 and 60 L/min) and placing the device close to the nasal cannula (in comparison with a position on the dry side of the humidification chamber). The use of a spacer was associated with higher delivery. The highest albuterol delivery was observed placing the spacer close to the nasal cannula, oriented for aerosol delivery following the gas flow and a 30 L/min NHF rate. Using this optimal setting, activating the pMDI at the beginning of inspiration (compared to expiration) increased albuterol delivery downstream of the nasopharyngeal cast. Whether in a quiet- or distress-breathing pattern, our measurements showed an amount of albuterol potentially delivered to the lungs exceeding 10% of the actuated dose in optimal conditions. Conclusions: Albuterol delivery with pMDIs is feasible within NHF circuits. Drug delivery sufficient to induce bronchodilation can be achieved using a spacer placed just upstream of the nasal cannula, a low NHF rate, and activation of the pMDI at the beginning of inspiration. Further testing in a clinical setting is required, however.

Humidified and Heated Cascade Impactor for Aerosol Sizing.

Aerosol sizing is generally measured at ambient air but human airways have different temperature (37°C) and relative humidity (100%) which can affect particle size in airways and consequently deposition prediction. This work aimed to develop and evaluate a new method using cascade impactor to measure particle size at human physiological temperature and humidity (HPTH) taking into account ambient air conditions. A heated and humidified trachea was built and a cascade impactor was heated to 37°C and humidified inside. Four medical aerosols [jet nebulizer, mesh nebulizer, Presurized Metered Dose Inhaler (pMDI), and Dry Powder Inhaler (DPI)] under ambient conditions and at HPTH were tested. MMAD was lower at HPTH for the two nebulizers; it was similar at ambient conditions and HPTH for pMDI, and the mass of particles smaller than 5 µm decreased for DPI at HPTH (51.9 vs. 82.8 µg/puff). In conclusion, we developed a new method to measure particle size at HPTH affecting deposition prediction with relevance. In vivo studies are required to evaluate the interest of this new model to improve the precision of deposition prediction.

Controlled Heat and Humidity-Based Treatment for the Reuse of Personal Protective Equipment: A Pragmatic Proof-of-Concept to Address the Mass Shortage of Surgical Masks and N95/FFP2 Respirators and to Prevent the SARS-CoV2 Transmission.

Background: The coronavirus infectious disease-2019 (COVID-19) pandemic has led to an unprecedented shortage of healthcare resources, primarily personal protective equipment like surgical masks, and N95/filtering face piece type 2 (FFP2) respirators. Objective: Reuse of surgical masks and N95/FFP2 respirators may circumvent the supply chain constraints and thus overcome mass shortage. Methods, design, setting, and measurement: Herein, we tested the effects of dry- and moist-air controlled heating treatment on structure and chemical integrity, decontamination yield, and filtration performance of surgical masks and FFP2 respirators. Results: We found that treatment in a climate chamber at 70°C during 1 h with 75% humidity rate was adequate for enabling substantial decontamination of both respiratory viruses, oropharyngeal bacteria, and model animal coronaviuses, while maintaining a satisfying filtering capacity. Limitations: Further studies are now required to confirm the feasibility of the whole process during routine practice. Conclusion: Our findings provide compelling evidence for the recycling of pre-used surgical masks and N95/FFP2 respirators in case of imminent mass shortfall.

Low-Frequency Intrapulmonary Percussive Ventilation Increases Aerosol Penetration in a 2-Compartment Physical Model of Fibrotic Lung Disease.

In patients with fibrotic pulmonary disease such as idiopathic pulmonary fibrosis (IPF), inhaled aerosols deposit mostly in the less affected region of the lungs, resulting in suboptimal pharmacokinetics of airway-delivered treatments. Refinement of aerosol delivery technique requires new models to simulate the major alterations of lung physiology associated with IPF, i.e., heterogeneously reduced lung compliance and increased airway caliber. A novel physical model of the respiratory system was constructed to simulate aerosol drug delivery in spontaneously breathing (negative pressure ventilation) IPF patients. The model comprises upper (Alberta ideal throat) and lower airway (plastic tubing) models and branches into two compartments (Michigan lung models) which differ in compliance and caliber of conducting airway. The model was able to reproduce the heterogeneous, compliance-dependent reduction in ventilation and aerosol penetration (using NaF as a model aerosol) seen in fibrotic lung regions in IPF. Of note, intrapulmonary percussive ventilation induced a 2-3-fold increase in aerosol penetration in the low-compliance/high airway caliber compartment of the model, demonstrating the responsiveness of the model to therapeutic intervention.

Protein stability during nebulization: Mind the collection step!

Inhaled protein therapeutics meet a growing interest for the treatment of respiratory diseases. In liquid aerosols, proteins face stresses that may generate instabilities, such as physicochemical denaturations, aggregation and loss of activity. Monitoring protein stability is thus crucial but implies collection of aerosol droplets before analysis. Many aerosol collection methods may be used, still their interference on protein stability is unknown. In this study, we compared the impact of six aerosol samplers on the stability of a model monoclonal antibody (Ig1), aerosolized with a mesh nebulizer. Ig1 stability was assessed for aggregation and biological activity. The six aerosol samplers generated distinct aggregation profiles for Ig1 at all size scales; counts of micron-sized particles varied by a factor of 100. The heterogeneity did not impact Ig1 activity, which was not significantly changed after nebulization. To extrapolate these results, we evaluated the impact of two samplers on three other proteins. Depending on the protein, samplers gave discordant aggregation and/or activity profiles, sometimes in the reverse trend as compared to Ig1. In conclusion, aerosol samplers interfere with protein stability; this impact depends both on the samplers and the protein, highlighting the importance of using the same collection device throughout the aerosol development process.

Innovative preclinical models for pulmonary drug delivery research.

Introduction: Pulmonary drug delivery is a complex field of research combining physics which drive aerosol transport and deposition and biology which underpins efficacy and toxicity of inhaled drugs. A myriad of preclinical methods, ranging from in-silico to in-vitro, ex-vivo and in-vivo, can be implemented.Areas covered: The present review covers in-silico mathematical and computational fluid dynamics modelization of aerosol deposition, cascade impactor technology to estimated drug delivery and deposition, advanced in-vitro cell culture methods and associated aerosol exposure, lung-on-chip technology, ex-vivo modeling, in-vivo inhaled drug delivery, lung imaging, and longitudinal pharmacokinetic analysis.Expert opinion: No single preclinical model can be advocated; all methods are fundamentally complementary and should be implemented based on benefits and drawbacks to answer specific scientific questions. The overall best scientific strategy depends, among others, on the product under investigations, inhalation device design, disease of interest, clinical patient population, previous knowledge. Preclinical testing is not to be separated from clinical evaluation, as small proof-of-concept clinical studies or conversely large-scale clinical big data may inform preclinical testing. The extend of expertise required for such translational research is unlikely to be found in one single laboratory calling for the setup of multinational large-scale research consortiums.

A consensus research agenda for optimising nasal drug delivery.

Nasal drug delivery has specific challenges which are distinct from oral inhalation, alongside which it is often considered. The next generation of nasal products will be required to deliver new classes of molecule, e.g. vaccines, biologics and drugs with action in the brain or sinuses, to local and systemic therapeutic targets. Innovations and new tools/knowledge are required to design products to deliver these therapeutic agents to the right target at the right time in the right patients. We report the outcomes of an expert meeting convened to consider gaps in knowledge and unmet research needs in terms of (i) formulation and devices, (ii) meaningful product characterization and modeling, (iii) opportunities to modify absorption and clearance. Important research questions were identified in the areas of device and formulation innovation, critical quality attributes for different nasal products, development of nasal casts for drug deposition studies, improved experimental models, the use of simulations and nasal delivery in special populations. We offer these questions as a stimulus to research and suggest that they might be addressed most effectively by collaborative research endeavors.